Getting a bit frustrated I can’t figure this out and I’m sure its something simple. Im attempting to run the test Crown file but once I run the GCode in Repetier it moves extremely slow. Can you guys take a look at my settings and the GCode and see if you can tell what is incorrect.
;Created by Estlcam version 11 build 11.244
;Machining time about 07:58:22 hours
G90
M03 S24000
G00 X0.0000 Y0.0000 Z0.0000 F2100
G00 Z5.0000 F480
;No. 1: Engraving 5
G00 X159.0227 Y41.3307 F2100
G00 Z0.5000 F480
G01 Z0.0000 F6 S24000
G01 Z-1.0000 F6
X209.4213 Y40.0369 I13.2045 J-467.8979 F15
X247.4842 Y34.9738 I-28.4080 J-359.1636 F15
X267.4293 Y30.3717 I-43.5857 J-234.4195 F15
X268.3420 Y28.4565 I-0.6098 J-1.4657 F15
G01 X266.8889 Y23.5346 F15
X264.9594 Y22.4497 I-1.5225 J0.4495 F15
X237.7054 Y28.2406 I-68.8399 J-256.9568 F15
X197.3433 Y32.4713 I-59.7772 J-375.6364 F15
X135.7849 Y31.7122 I-25.0244 J-467.0296 F15
X98.7074 Y26.8306 I27.3178 J-350.7353 F15
X79.2919 Y22.4102 I48.2760 J-256.8886 F15
X77.5626 Y23.5346 I-0.2068 J1.5740 F15
G01 X76.1095 Y28.4565 F15
X77.2220 Y30.4397 I1.5225 J0.4495 F15
X105.2351 Y36.4358 I70.9019 J-262.8095 F15
X146.6120 Y40.8246 I61.5688 J-383.2142 F15
G01 X152.7099 Y41.1156 F15
G01 X159.0011 Y41.3301 F15
G01 Z-2.0000 F6
X114.3376 Y37.7972 I10.3955 J-415.5056 F15
X82.9517 Y31.9291 I39.8468 J-299.9928 F15
G01 X79.9756 Y31.1758 F15
G01 X77.2220 Y30.4397 F15
X76.1095 Y28.4565 I0.4100 J-1.5336 F15
G01 X77.5626 Y23.5346 F15
X79.4921 Y22.4497 I1.5225 J0.4495 F15
X106.7461 Y28.2406 I68.8399 J-256.9568 F15
X147.1082 Y32.4713 I59.7772 J-375.6364 F15
X208.6666 Y31.7122 I25.0244 J-467.0296 F15
X245.7441 Y26.8306 I-27.3178 J-350.7353 F15
X265.1595 Y22.4102 I-48.2760 J-256.8886 F15
X266.8889 Y23.5346 I0.2068 J1.5740 F15
G01 X268.3420 Y28.4565 F15
X267.2295 Y30.4397 I-1.5225 J0.4495 F15
X239.2163 Y36.4358 I-70.9019 J-262.8094 F15
X197.8395 Y40.8246 I-61.5688 J-383.2142 F15
X159.0227 Y41.3307 I-25.6940 J-481.8654 F15
G00 Z5.0000 F480
