|
Please read before asking LowRider questions. Help us, better help you, thanks!
|
|
0
|
1051
|
November 23, 2019
|
|
X axis not working properly
|
|
24
|
56
|
May 18, 2024
|
|
Jackpot cnc controller, port b not working
|
|
54
|
117
|
May 18, 2024
|
|
Help again!
|
|
13
|
99
|
May 18, 2024
|
|
X axis motor is playing up
|
|
7
|
56
|
May 18, 2024
|
|
X Axis fitment
|
|
198
|
1489
|
May 17, 2024
|
|
No Printer Attached issue
|
|
27
|
131
|
May 16, 2024
|
|
Screen is blank. I need some help
|
|
5
|
35
|
May 12, 2024
|
|
Z probe problem
|
|
10
|
83
|
May 11, 2024
|
|
LR3 traming - X and Y direction
|
|
170
|
2986
|
May 11, 2024
|
|
I can crash my z axis with my shopvac!
|
|
2
|
66
|
May 8, 2024
|
|
X end stop pin not working
|
|
1
|
57
|
May 5, 2024
|
|
Same Power Supply as Arduino+CNC Shield V3
|
|
4
|
77
|
May 3, 2024
|
|
Unable to run gcode file with Octoprint
|
|
9
|
57
|
April 30, 2024
|
|
LR3 freezes after 2-3 commands after flashing 3.7.16 (jackpot controller) EDIT: 3.7.16 firmware was the problem
|
|
10
|
112
|
April 28, 2024
|
|
Y axis not traveling full length of bed
|
|
8
|
81
|
April 28, 2024
|
|
Workflow recommendation for z-probe
|
|
11
|
259
|
April 27, 2024
|
|
Touch plate end stop always in a triggered state
|
|
4
|
53
|
April 25, 2024
|
|
Jackpot power supply tripping GFCI
|
|
7
|
115
|
April 23, 2024
|
|
Not sure what to adjust?
|
|
18
|
303
|
April 22, 2024
|
|
Z axis started droping on one side
|
|
12
|
570
|
April 16, 2024
|
|
Cutting a square and circle, but they are out of measurements or oval
|
|
5
|
118
|
April 16, 2024
|
|
Issue with TMC 2209 - TMC connection error (motor was working before)
|
|
1
|
74
|
April 8, 2024
|
|
Stepper motor config - 17HE19-2004S
|
|
9
|
319
|
April 7, 2024
|
|
Z axis dilemma
|
|
5
|
138
|
April 4, 2024
|
|
Weird issue tramming, spoil surfacing - hive mind help?
|
|
4
|
161
|
April 3, 2024
|
|
Test cut not aligning properly - Help needed!
|
|
6
|
84
|
April 1, 2024
|
|
Laser problem advice required
|
|
4
|
83
|
March 31, 2024
|
|
Problem with x not stopping when homing
|
|
41
|
1272
|
March 31, 2024
|
|
Y axis is off by a few mm
|
|
2
|
105
|
March 30, 2024
|
