|
About the Hardware Development category
|
|
0
|
492
|
November 23, 2019
|
|
Laser: NEJE A40640 versus new NEJE E40 - thoughts?
|
|
17
|
331
|
October 6, 2022
|
|
LR 2.5" hose quick connect/LR3 mount
|
|
1
|
64
|
October 2, 2022
|
|
Interchangeable Tool Mount System, Laser, Needle Cutter, Pen, Drag Knife
|
|
13
|
1042
|
September 30, 2022
|
|
LowRider 3 CNC - control box case for BTT SKR Pro 1.2 board and a BTT TFT35 E3 touchscreen (v1.2)
|
|
79
|
1143
|
September 29, 2022
|
|
Xtool has a new quad diode 20w laser and they're supposed to be filling pre-orders of it
|
|
15
|
271
|
September 28, 2022
|
|
Use laser cut on lowrider2
|
|
8
|
100
|
September 26, 2022
|
|
New short video: LR3 CNC "Grid Power" -
|
|
2
|
141
|
September 19, 2022
|
|
LowRider 3 CNC - control box case for BTT SKR 1.4 Turbo board, Raspberry Pi 4b, and BTT TFT35 E3 touchscreen (v1.3.5)
|
|
0
|
105
|
September 16, 2022
|
|
LowRider 3 CNC - control box case for Raspberry Pi 4b, BTT SKR Pro 1.2 board, and BTT TFT35 E3 touchscreen (v1.3.3)
|
|
1
|
98
|
September 16, 2022
|
|
LowRider 3 CNC Plasma Torch Mount with floating Z and magnetic breakaway, prints without supports (v1.2)
|
|
0
|
73
|
September 10, 2022
|
|
Grblgru, Lowrider 2, virtual simulation, 5 axis
|
|
54
|
7636
|
September 9, 2022
|
|
LR2 – Z axis square tool?
|
|
4
|
119
|
September 4, 2022
|
|
X axis belt tensioner with m5 square nut trap - will not allow nut to rotate within trap
|
|
0
|
65
|
September 3, 2022
|
|
Is there a decent pen/drag knife mount for the LR3 out there yet?
|
|
7
|
176
|
September 3, 2022
|
|
LowRider 3 CNC - control box case for BTT SKR Pro 1.2 board and a BTT TFT35 E3 touchscreen (v1.3.4) SHORTER VERSION (180mm) FOR SHORTER PRINTERS
|
|
0
|
78
|
September 2, 2022
|
|
Low Rider 3 y axis belt holder with adjustable endstop target
|
|
2
|
102
|
September 1, 2022
|
|
Upgrade the motors on LR3
|
|
19
|
342
|
August 29, 2022
|
|
LR3 Adjustable Height
|
|
18
|
745
|
August 24, 2022
|
|
Bosch 1617EVS tool mount for low rider 3
|
|
1
|
116
|
August 23, 2022
|
|
LowRider 3 CNC, LR3 Release notes
|
|
372
|
8393
|
August 22, 2022
|
|
End Cap for 1/2" EMT Tube (v1.0)
|
|
5
|
172
|
August 18, 2022
|
|
LowRider v3 - Cable Chain Mount (v1.0)
|
|
6
|
342
|
August 15, 2022
|
|
End Cap for 1.5" Square Tube (1/8" wall)
|
|
0
|
125
|
August 12, 2022
|
|
Printable Cable Chain for CNC, two-piece, snap-open, 20mm x 40mm, 64mm radius (v1.12)
|
|
44
|
587
|
August 11, 2022
|
|
Dust Collection Adapter for SKIL 10-inch Worm Drive Table Saw, going from 2.5" (ID 64mm) to 2.25" (ID 57mm) v1.0
|
|
4
|
121
|
August 10, 2022
|
|
LowRider v3 - LR3 control box case for SKR Pro 1.2 with TFT35 E3 (based on V1’s Blank Case CAD files)
|
|
10
|
492
|
August 9, 2022
|
|
Anyone? Lowrider2 skr2 w/tft35 e3 case
|
|
0
|
80
|
August 6, 2022
|
|
LowRider v3 plasma CNC - Drag Chain Mount revised for large 20x40 drag chain (v1.1)
|
|
0
|
126
|
August 5, 2022
|
|
LR3 Mod Y Tensioner block, going topless for easy mid belt access? Goal: Enable faster swap between big and little table
|
|
0
|
122
|
July 30, 2022
|
